2 Hp 110 120 V Ac 1500 Watt Industrial Servo Motor Controller Driver External

2 hp 110 120 V AC 1500 watt industrial servo motor controller Driver external

2 hp 110 120 V AC 1500 watt industrial servo motor controller Driver external

2 hp 110 120 V AC 1500 watt industrial servo motor controller Driver external


2 hp 110 120 V AC 1500 watt industrial servo motor controller Driver external


2 hp 110 120 V AC 1500 watt industrial servo motor controller Driver external

2 hp 110 120 V AC 1500 watt industrial servo motor controller Driver external
2 hp 110 120 V AC 1500 watt industrial servo motor controller Driver external


2 hp 110 120 V AC 1500 watt industrial servo motor controller Driver external

  2 hp 110 120 V AC 1500 watt industrial servo motor controller Driver external

2 HP 1500 Watt Computer Controlled Servo Motor With E xternal Speed Control Switch. For any range between 300 to 3,500 RPM. Note: the maximum distance between control unit and motor is 22 inches. Runs on typical 110 to 120 volt AC. A complete servo motor as seen in images.

Custom built servo motor driver with overload protection. Variable speed control rotary switch.

Toothed L050 pulley not included. Note I can cut, broach and fit any pulley you chose at additional cost. One 1,500 watt (2 HP) servo motor. And a thermal overload system. I have a functioning break out PCB that allows for remote control. Forward and an emergency stop. Each of the three speeds can be set as follows. Anywhere between 300 and 1,000 RPM. Anywhere between 900 and 3,200 RPM. Anywhere between 2,000 and 4,500 RPM. Emergency cut off/power stop function. Each of which is energized by a single on off contact via wire.
Connectors on the back of the control unit. Motor programming + spindle speeds and Reverse. The motor speed can be programmed to operate in any range chosen by the user. Between 300 and 3,500 RPM's. The full range of speed (RPM's) can also be controlled with just the speed control knob.

Only requires a few easy steps. Reverse is simple, just hold the yellow button for a few seconds. Includes the ability to set bottom and top RPM range separately.

In other words you can program the system to run the spindle at any speed or range of speeds you choose (see below). Slowest speed achievable: Motor 200 RPM. (Below 300 is not recommended). Highest speed: 3,500 RPM. Can be programmed to reach 5,000 RPM.
This is seriously not recommended. It is also dangerous as in parts could fly across the room causing serious bodily injury even death. Setting above 3,500 RPM also voids.

Soft start is programmable and will be set as soft as possible when you receive this motor. This program is very effective in reducing drive belt wear etc. Braking strength is also programmable and will be set as low as possible.

Personally I wish I could set it lower. Safe turn on system where the speed control knob must be in the full counter clockwise (stop) position when turned on. When turned on the self. System checks for faults and will not allow the motor to turn on until the speed control knob is turned all the way to stop first. Control unit has the ability to stop the motor or what ever it is turning in 2 different locations with external hall effect sensors not included.

To communicate with any CNC. Use at your own risk. This listing is for what is seen in the primary image. It will include printed programming instructions. Have this on my taig lathe with 5c headstock and wow!! 2 hp 110 120 V AC 1500 watt industrial servo motor & controller Driver Updated. Large flat rate box and to USA only.

This item will be is strict. Applied to this item when it was listed. See details, what's covered and for how long etc below. If found to be abuse or missing the. Or demos that I have from previous builds.

Additionally original packaging such as Styrofoam package inserts must be used to return these parts. Ask lots of questions before ordering. Do not worry about missing this item. If you miss it, I will get more soon. The item "2 hp 110 120 V AC 1500 watt industrial servo motor controller Driver external" is in sale since Sunday, February 14, 2021.

This item is in the category "Home & Garden\Tools & Workshop Equipment\Power Tools\Lathes". The seller is "thecustomcrafter" and is located in Haines City, Florida. This item can be shipped to United States.

  • Model: Prototype 5
  • Machine Type: Servo Motor
  • Model Year: 2021
  • Power Source: Home electric outlets
  • MPN: Does Not Apply
  • Minimum Spindle Speed: 200
  • Type: Lathes, milling machines, band saws and more
  • Phase: One Phase
  • Maximum Spindle Speed: 3.500
  • Brand: The Custom Crafter
  • Manufacturer Warranty: See description.
  • Suitable For: Aluminum
  • Control: Programmable Speed Control
  • Voltage: 110 V, 115, V 120 V


2 hp 110 120 V AC 1500 watt industrial servo motor controller Driver external

  2 hp 110 120 V AC 1500 watt industrial servo motor controller Driver external